Type ASNU is a roller type freewheel non-bearing supported. Bearings are required to support axial and radial loads. Lubrication and sealing must also be provided by the installation. Nominal outer diameter is the same as a series 63.. ball bearing.
A typical arrangement is to install this type alongside a bearing within the same location tolerances, as shown on the following page. The inner race is keyed to the shaft. The outer race has positive n6 tolerance, to give a press fit in a H7 housing. Additional side notches in the outer race provide for positive torque transmission.
If the housing is to K6 tolerance, use of the notches is not necessary, but the housing must be strong enough to not expand after assembly. This design can accept an axial misalignment of inner and outer race of ± S/2.
Data
Drawing legend
d=inner diameter D=outer diameter L = width TKN = torque n = rotation speed b = keyway width t = keyway depth
Type |
Size |
|
Overrunning Speeds |
|
Weight |
Drag torque |
ASNU |
dH7 |
TKN1) |
nimax2) |
namax3) |
Dn6 |
D5 |
L |
b |
t |
s |
e |
f |
|
TR |
[mm] |
[Nm] |
[min-1] |
[min-1] |
[mm] |
[mm] |
[mm] |
[mm] |
[mm] |
[mm] |
[mm] |
[mm] |
[kg] |
[Ncm] |
8 |
12 |
3300 |
5000 |
35 |
28 |
13 |
4 |
1.4 |
2.4 |
0.6 |
0.3 |
0.07 |
1.6 |
12 |
12 |
3300 |
5000 |
35 |
28 |
13 |
4 |
1.4 |
2.4 |
0.6 |
0.3 |
0.06 |
1.6 |
15 |
30 |
2400 |
3600 |
42 |
37 |
18 |
5 |
1.8 |
2.4 |
0.8 |
0.3 |
0.11 |
1.9 |
17 |
49 |
2300 |
3400 |
47 |
40 |
19 |
5 |
2.3 |
2.4 |
1.2 |
0.8 |
0.15 |
1.9 |
20 |
78 |
2100 |
3100 |
52 |
42 |
21 |
6 |
2.3 |
2.4 |
1.2 |
0.8 |
0.19 |
1.9 |
25 |
125 |
1700 |
2600 |
62 |
51 |
24 |
8 |
2.8 |
2.4 |
1.2 |
0.8 |
0.38 |
5.6 |
30 |
255 |
1400 |
2200 |
72 |
60 |
27 |
10 |
2.5 |
2.4 |
1.8 |
1 |
0.54 |
14 |
35 |
383 |
1200 |
1900 |
80 |
70 |
31 |
12 |
3.5 |
2.4 |
1.8 |
1 |
0.74 |
16 |
40 |
538 |
1100 |
1700 |
90 |
78 |
33 |
12 |
4.1 |
2.5 |
1.8 |
1 |
0.92 |
38 |
45 |
780 |
1000 |
1600 |
100 |
85 |
36 |
14 |
4.6 |
2.5 |
1.8 |
1 |
1.31 |
43 |
50 |
1013 |
850 |
1350 |
110 |
92 |
40 |
14 |
5.6 |
2.5 |
1.8 |
1 |
1.74 |
55 |
60 |
1825 |
750 |
1050 |
130 |
110 |
46 |
18 |
5.5 |
3.6 |
2.6 |
1.5 |
2.77 |
110 |
70 |
2300 |
600 |
950 |
150 |
125 |
51 |
20 |
6.9 |
3.6 |
2.6 |
1.5 |
4.16 |
140 |
80 |
3275 |
550 |
850 |
170 |
140 |
58 |
20 |
7.5 |
3.6 |
2.6 |
1.5 |
6.09 |
180 |
90 |
5325 |
500 |
750 |
190 |
160 |
64 |
20 |
8 |
3.6 |
2.6 |
2 |
8.2 |
230 |
100 |
7250 |
450 |
680 |
215 |
175 |
73 |
24 |
8.5 |
3.6 |
2.6 |
2 |
12.6 |
380 |
120 |
13500 |
370 |
550 |
260 |
215 |
86 |
28 |
10 |
3.6 |
2.6 |
2.5 |
22 |
650 |
150 |
26625 |
300 |
460 |
320 |
260 |
108 |
32 |
12 |
3.6 |
3.6 |
2.5 |
42 |
1000 |
200 |
44500 |
230 |
350 |
420 |
350 |
138 |
45 |
16 |
7.6 |
3.6 |
3 |
93 |
2000 |
Notes:
ASNU8-12,ASNU200 keyway to DIN6885.1,other size to DIN6885.3
1)Tmax=2.5*tkn
2)Inner race overrunns
3)Outer race overrunns